Search:

Type: Posts; User: Bjorn_K

Page 1 of 15 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    342

    Is there a reason why your Points are a Nested...

    Is there a reason why your Points are a Nested list? If not, Flatten that list, get rid of the @L in the Room.By Location and that should do it.
  2. From a quick look it seems like you're asking for...

    From a quick look it seems like you're asking for an item in a lost that is only 1 item long, resulting in your nulls.

    For the sorting, I would make a Sheet Number - View Element Dictionary, then...
  3. It's in the Visibility Settings, under Site:...

    It's in the Visibility Settings, under Site: Project Internal
  4. Turn it off in your View Templates. If those...

    Turn it off in your View Templates.

    If those views are not controlled by templates, you should research them.
  5. Replies
    1
    Views
    468

    This is easy with a Dictionary, where the Key is...

    This is easy with a Dictionary, where the Key is the string (Name) of the Country and the Value is the Title Block Type that you need for that country.

    The Drop Down will result in the Name, the...
  6. Replies
    5
    Views
    484

    Is your ViewID a Type parameter?

    Is your ViewID a Type parameter?
  7. Replies
    11
    Views
    2,070

    Some quick suggestions: -2 schedules on the...

    Some quick suggestions:

    -2 schedules on the Sheet. 1 with the doors To the specific Room, 1 with the door From the specific Room.

    -Concatenate the values from Room From:Number and Room...
  8. If you want to go this route you need to make...

    If you want to go this route you need to make Types for the Section Head family and assign them to different Section Types.
  9. Replies
    3
    Views
    630

    make the panel, nest it into a Family with a...

    make the panel, nest it into a Family with a Refline to rotate for pitch, host on that Refline, nest that into a family with a Refline for direction.
  10. Replies
    2
    Views
    948

    Check if there is not actually 2 Toposurfaces...

    Check if there is not actually 2 Toposurfaces there.
  11. Yep, don't "cheat" the truss. Alternative to...

    Yep, don't "cheat" the truss.

    Alternative to Alfs suggestion, if you're dead set on doing it in the CME environment, create an 2pt adaptive component, you will be able to snap to the edges of your...
  12. Replies
    7
    Views
    1,052

    Have you tried the example? Because this: ...

    Have you tried the example? Because this:



    is exactly what the example is doing.




    I have no idea how you would arrive at this conclusion if you had tried to make some scripts with some...
  13. Replies
    7
    Views
    1,052

    Turns out the almighty Clockwork has the...

    Turns out the almighty Clockwork has the MassFloor.Mass Node.

    37548
  14. The void is in the Family itself, you include the...

    The void is in the Family itself, you include the end condition in the Family. Maybe as a variable to also take care of angles other than 45 degrees.
  15. Connect your adaptive points with Reference Lines...

    Connect your adaptive points with Reference Lines (Draw on Face, 3D Snapping ON)

    Place a point on those lines, make sure you hover over the line and the resulting point will look smaller than the...
  16. Replies
    13
    Views
    2,060

    As a general tip here: Revit doesn't recognize a...

    As a general tip here: Revit doesn't recognize a rounded object in projection as an edge to dimension to. I usually try to include Reference Planes in my families in those conditions so the user can...
  17. The text will be there, but it will not be in the...

    The text will be there, but it will not be in the actual Dimension element. It will be an extra element (TAG) reading the Name/Description field from the actual element.

    That way you get rid of...
  18. Why the need to have the text IN the Dim? I...

    Why the need to have the text IN the Dim?

    I see a fully automated Tag reading the information from the modelled element sitting next to a Dimension String. Both fully automatic with good content,...
  19. Replies
    16
    Views
    1,214

    Why do that dude? Not conducive to growing a...

    Why do that dude? Not conducive to growing a healthy atmosphere in a community at all.

    The Question is 100% valid, I have run into 3 meanings for "Working Drawings" (Finely detailed drawings from...
  20. Replies
    4
    Views
    479

    What did you try so far? It is possible to get...

    What did you try so far?

    It is possible to get elements from Linked Files:
    37253

    So maybe something like:

    Select your Recess Families, extract their placement point (or something similar),...
  21. Replies
    39
    Views
    2,267

    100% my experience as well.

    100% my experience as well.
  22. Replies
    6
    Views
    700

    Eliminate the Elements in Room Node from your...

    Eliminate the Elements in Room Node from your process to troubleshoot if it's the Node or the Revit elements.(What Package is it from, have you looked in the Node itself?)

    The Rooms are in a...
  23. Replies
    12
    Views
    1,225

    Edge Of Slab.

    Edge Of Slab.
  24. Replies
    5
    Views
    588

    Not sure about the actual View Reference...

    Not sure about the actual View Reference placement through Dynamo, but I am switching the Viewport Types with Dynamo after placing the Viewports on the Sheets. It's not directly controlling the View...
  25. Replies
    4
    Views
    944

    Are you in the CME? Then hit spacebar to toggle...

    Are you in the CME? Then hit spacebar to toggle local/global XYZ axis.
Results 1 to 25 of 359
Page 1 of 15 1 2 3 4