Search:

Type: Posts; User: Andrew K

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    0
    Views
    431

    Flow Parameter unit change - heads up

    In case people were not aware, the imperial units for flow rate in piping changed. In years 2020 and below, flow rate parameter units were in gallons_us_per_minute. In 2021, flow rate parameter units...
  2. Replies
    4
    Views
    720

    You can host it to another reference line drawn...

    You can host it to another reference line drawn in plan and rotate the new one, if I am understanding your request.
  3. Replies
    16
    Views
    5,515

    Getting video adverts again when looking at a...

    Getting video adverts again when looking at a thread, also while typing this reply. Is this an intentional or unintentional event?
  4. Replies
    25
    Views
    7,969

    I've asked a handful of times if they wanted...

    I've asked a handful of times if they wanted assistance with that, but no positive responses thus far.
  5. Replies
    5
    Views
    993

    There are only three values missing on that one...

    There are only three values missing on that one type. If the manufacturer has a product page, you can try filling the values in yourself. You can open the type catalog in a comma delimited excel to...
  6. Replies
    5
    Views
    993

    The last type entry, MSRDEE1400, is missing...

    The last type entry, MSRDEE1400, is missing values in three parameters.
  7. Thread: Type Catalog

    by Andrew K
    Replies
    10
    Views
    2,971

    Beyond the inability to import the type catalog...

    Beyond the inability to import the type catalog in the family editor, why do you say that?
  8. Replies
    10
    Views
    2,107

    Since you have 'Room Dimensions Visibility' being...

    Since you have 'Room Dimensions Visibility' being controlled by 'Room Area Visibility', your third parameter will never work as one of those two options will always be on.

    You may want to rethink...
  9. Thread: Arraying

    by Andrew K
    Replies
    5
    Views
    1,524

    What are the minimum and maximum number of...

    What are the minimum and maximum number of support members? Array will likely not be the way to go if you need individual length adjustments.
  10. Thread: nive flange

    by Andrew K
    Replies
    3
    Views
    1,628

    Are you making the flanges with a lookup table or...

    Are you making the flanges with a lookup table or a different method?
  11. If you don't want to place the blades again, host...

    If you don't want to place the blades again, host the blades to a reference line in a right/left elevation and rotate the reference line 90 degrees.
  12. Replies
    9
    Views
    3,861

    When using nested elements, you should control...

    When using nested elements, you should control both visibility options. It isn't enough to unsee the linework, you need to disable the nested element.

    In the image, I nested a linework circle into...
  13. Replies
    4
    Views
    2,929

    The view is either corrupt and should be deleted...

    The view is either corrupt and should be deleted or the family is modeled in a way that would make it not show properly.

    Do you have permission to post a screenshot?
  14. If you modeled it as a sweep, change the profile....

    If you modeled it as a sweep, change the profile.

    If you modeled it with another method, let us know what you did.
  15. Replies
    16
    Views
    5,515

    Happening with me, too. So far they are...

    Happening with me, too. So far they are unobtrusive, but I thought that users logged in would not be seeing (or see a reduced amount) of ads. They auto cycle to different ads, some with video, every...
  16. When I had built it, I did not think it was going...

    When I had built it, I did not think it was going to be necessary for it to be able to move from the surface. The dimension is 3" due to the extents of the extrusion making up the cover.

    It is...
  17. Try changing the naming scheme of the parameters...

    Try changing the naming scheme of the parameters that have the _. From what I remember it does not like them too much.

    Might also help to show us your lookup formulas in the family to see if those...
  18. Have your egress factor be its own 'number'...

    Have your egress factor be its own 'number' parameter. Then, in the formula have it read (ECF * 0' 1") instead of (19/128). That will get you closer to the required number.

    Or, if you want it to...
  19. My solution should only be for situations where...

    My solution should only be for situations where you have surface mounted/semi-recessed/recessed in the same family on a face-based template. For what you want to do, you'd be better off making an...
  20. Replies
    37
    Views
    9,690

    What Aaron said in his first post is generally...

    What Aaron said in his first post is generally what all door content should eventually be.

    The hardest thing about using manufacturer door content is that there is no 'one way' to develop certain...
  21. Thread: Math Help

    by Andrew K
    Replies
    9
    Views
    3,166

    Is the spacing between elements always going to...

    Is the spacing between elements always going to be 130? Why is your input not the number of grids but the length of the claustra? You will always have a remainder on the last grid element unless you...
  22. Replies
    5
    Views
    1,607

    You did not finish your formula string the first...

    You did not finish your formula string the first time around. It's missing the end "THEN" value and missing an if statement.

    You can end the formula at :

    if(Diameter < 700 mm, ((Ext radius +...
  23. When using the array tool in the family editor,...

    When using the array tool in the family editor, it is always best practice to 'nest'/load in the arrayed component.
  24. You dimensioned to the geometry of your fixture...

    You dimensioned to the geometry of your fixture rather than use reference planes. That's why you're having trouble constraining the cable extrusions.
  25. Are you linking the array number to a label or...

    Are you linking the array number to a label or writing the parameter into the field? It looks like you're trying to write the parameter name inside the array count field.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4